PTFE rods from 100% pure PTFE by molding, turning, cutting and other refined from the known plastics, it has the best chemical resistance, aging, electrical insulation , And has a very low coefficient of friction in the case of no load, can be -180 ~ +260 degrees temperature use. Uses: flat pad, V-pad, lining material, etc. Sealing materials: piston rings, rails and other lubricating materials: Electrical insulation materials: anti-sticking materials. PTFE rod has three specifications: Push PTFE rod. Extruded PTFE rod, PTFE Rod molded PTFE rod diameter 4mm ~ 9mm bar made of selected dispersion polytetrafluoroethylene resin paste diameter paste made of diameter 10mm ~ 50mm rod made of PTFE resin used by the plunger extrusion Processed into a diameter of 55mm ~ 300mm rods made by the molding process.
Teflon rods are two kinds of rods and molded rods. Polytetrafluoroethylene has the best chemical resistance and dielectric properties in known plastics. It can be used at a temperature of -180 ℃ - + 260 ℃, As well as the lowest coefficient of friction, mainly for a number of long products and non-standard specifications of the mechanical parts: seals / washers, ring, wear plate / Block, insulating parts, PTFE Rod corrosion resistance industry, machinery parts, lining, oil And natural gas, petrochemical industry, chemical industry, equipment manufacturers.
Chemical: can be used as anti-corrosion materials, can manufacture a variety of anti-corrosion parts, such as pipes, valves, pumps and fittings joints. Chemical equipment, can be produced reactor, distillation column and anti-corrosion equipment lining and coating.
Mechanical: can be used as self-lubricating bearings, piston rings, PTFE Rod oil seals and seals. Self-lubrication can reduce wear and heat and reduce power consumption.
Electronic and electrical aspects: mainly used in the manufacture of various wire and cable, battery electrodes, battery separator, printed circuit boards.
Medical materials: the use of its heat, water, non-toxic properties, PTFE Rod can be used as a variety of medical equipment and artificial organs of the material. The former such as disinfection filters, beakers, artificial heart and lung devices, the latter such as artificial blood vessels, PTFE Rod heart and esophagus and so on. It has been widely used as a sealing material and a filling material.
Teflon rod characteristics
Operating temperature range is very wide (-200 degrees Celsius to +260 degrees).
Basically corrosion resistant to all chemicals except for some fluorides and alkaline metals.
Excellent mechanical properties, including anti-aging, PTFE Rod especially for bending and swinging applications.
Outstanding flame retardancy (meets ASTM-D635 and D470 test procedures, is defined as a flame retardant material in the air.
Excellent insulation properties (regardless of frequency and temperature)
Low water absorption, PTFE Rod and has a series of unique properties such as self-lubricating and non-sticky.
Teflon rod specifications
Plate: thickness * width = 0.3 ~ 1.5mmx300mm;
Thickness * width = 2 ~ 60mmx600mmx600mm;
Bar: Diameter: 6 ~ 200mm.x 200mm / 1000mm
Special size can be customized
- Common Misunderstanding Of Polytetrafluoroethyl...
- Teflon Engineering Plastics And General Plastic...
- Small Teflon Seal Behind The Story
- Application Of Polytetrafluoroethylene Engineer...
- Points For Attention In CNC Machining Of Polyte...
- PTFE Gasket Why The Use Of Failure
- Summary Of Leakage Mode Of PTFE Sealing Gasket
- A Brief Introduction To PTFE Packing
- Expanded PTFE Elastic Band Is Easy To Use And D...
- Aramid Graphite Packing And High Water - Based ...
- Teflon Tube Has Excellent Thermal Stability
- PTFE Gasket Has Good Mechanical Toughness